You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
{{ message }}
Repository navigation
[BUG][CML]Arecord0,4 rt715 captured audio files output pop noise #1969
The firmware PGA5.0 gain is sane. I traced volume volume channels 0 and 1 gains in every copy(), at 1 ms rate. The 400 ms ramp as defined in topology is similar for both channels without gain jumps.
Still the captured level envolope shows strange gain changes for both channels at 50 ms, 80ms, and for channel 0 only at 300 ms. The FW ramp envelope can be seen to last for both channels 400 ms that matches with previous plot.
The capture pipeline contains a 40 Hz high-pass IIR filter as it should. The low frequency down and up and down waveform is from DC signal that is emitted by the codec. I'll do a capture test with pipeline without IIR so it becomes better visisible.
The capture with IIR removed from pipeline looks like this:
The same gain changes can be seen as above but they "ride" above the huge DC level variation in the first 500 ms of the capture. Note: This picture is with less gain than the previous with IIR.
@mengdonglin@bardliao Do you happen to know contacts to codec driver developer? The control sequence that is applied to codec looks strange. It's not possible to mitigate any further the capture start artifacts with firmware than this.
Activity
[-][BUG][CML]Arecord0,4 rt715 captured audio files have "po" noise output.[/-][+][BUG][CML]Arecord0,4 rt715 captured audio files output "po" noise [/+]plbossart commentedon Apr 1, 2020
what does "po" mean?
[-][BUG][CML]Arecord0,4 rt715 captured audio files output "po" noise [/-][+][BUG][CML]Arecord0,4 rt715 captured audio files output pop noise [/+]plbossart commentedon May 27, 2020
@sinahuang isn't this fixed now? can we close?
sinahuang commentedon May 29, 2020
Issue still can be reproduced with sof-dev(commit: 0d22f66) +master(commit :caae629) on CML-H.
plbossart commentedon Jun 9, 2020
Indeed this doesn't look very good, see what I capture on my side.
@singalsu can you take a look? Maybe borrow @kv2019i 's SoundWire laptop to see what happens on the capture side?
singalsu commentedon Jun 10, 2020
@plbossart Yup, it looks strange. I'll get such device and test.
singalsu commentedon Jun 15, 2020
I have a suitable device now. The volume capture ramp does some really strange things, good that I can now replicate this:
(the different capture level on L & R does not matter, this was just a quick acoustical test)
singalsu commentedon Jul 2, 2020
This was on hold while I debugged ASRC. I repeated this with current SOF git development repos:
FW 7b532d3
kernel f6be379
The firmware PGA5.0 gain is sane. I traced volume volume channels 0 and 1 gains in every copy(), at 1 ms rate. The 400 ms ramp as defined in topology is similar for both channels without gain jumps.
Still the captured level envolope shows strange gain changes for both channels at 50 ms, 80ms, and for channel 0 only at 300 ms. The FW ramp envelope can be seen to last for both channels 400 ms that matches with previous plot.
The capture pipeline contains a 40 Hz high-pass IIR filter as it should. The low frequency down and up and down waveform is from DC signal that is emitted by the codec. I'll do a capture test with pipeline without IIR so it becomes better visisible.
singalsu commentedon Jul 2, 2020
The capture with IIR removed from pipeline looks like this:
The same gain changes can be seen as above but they "ride" above the huge DC level variation in the first 500 ms of the capture. Note: This picture is with less gain than the previous with IIR.
@mengdonglin @bardliao Do you happen to know contacts to codec driver developer? The control sequence that is applied to codec looks strange. It's not possible to mitigate any further the capture start artifacts with firmware than this.
24 remaining items
ASoC: rt715: Add module parameter to fix dmic pop sound issue.
ASoC: rt715: Add module parameter to fix dmic pop sound issue.
ASoC: rt715: Add module parameter to fix dmic pop sound issue.
ASoC: rt715: Add module parameter to fix dmic pop sound issue.
ASoC: rt715: Add module parameter to fix dmic pop sound issue.
ASoC: rt715: Add module parameter to fix dmic pop sound issue.
ASoC: rt715: Add module parameter to fix dmic pop sound issue.
ASoC: rt715: Add module parameter to fix dmic pop sound issue.
ASoC: rt715: Add module parameter to fix dmic pop sound issue.
ASoC: rt715: Add module parameter to fix dmic pop sound issue.
ASoC: rt715: Add module parameter to fix dmic pop sound issue.
ASoC: rt715: Add module parameter to fix dmic pop sound issue.
ASoC: rt715: Add power-up delay to fix dmic pop sound issue.
ASoC: rt715: Add power-up delay to fix dmic pop sound issue.
ASoC: rt715: Add power-up delay to fix dmic pop sound issue.